AeroGCS GREEN
  • AeroGCS GREEN User Manual
  • 1. Introduction
  • 2. System Requirements
  • 3. Getting Started
    • 3.1 Installing AeroGCS GREEN
    • 3.2 Activating AeroGCS GREEN
    • 3.3 Updating AeroGCS GREEN
      • 1. Play Store Update: The Classic Method
      • 2. Inline Update: Update on the Go!
  • 4. Dashboard
  • 5. Home Menu
  • 6. Projects
    • 6.1 Create a New Project
      • 6.1.1 Automatic Flying Method
      • 6.1.2 Manual Flying Method
    • 6.2 Handling Existing Project
      • 6.2.1 Open existing project
      • 6.2.2. Edit a Plan
      • 6.2.3 View and Edit the Plan Report
      • 6.2.4. Edit a plot
      • 6.2.5 Add a plot to the existing project
      • 6.2.6 Download Plot and Plan
      • 6.2.7 Delete a Project
        • 1: Not Logged in to AeroGCS Enterprise
        • 2: Logged in to AeroGCS Enterprise
  • 7. Connecting a Drone
    • 7.1. Using Serial Port
    • 7.2 Using TCP
    • 7.3 Using UDP
    • 7.4. Using Bluetooth
    • 7.5 Using H12
    • 7.6 Drone Registration
  • 8. RPA Settings
    • 8.1 Aircraft Settings
    • 8.2 Spraying system:
      • 8.2.1 Spray testing
      • 8.2.2 Spraying Parameters
      • 8.2.3 Clear Trapped Air
      • 8.2.4 Set Spray Tank Level
      • 8.2.5 Empty Threshold Action
      • 8.2.6 Flow Meter Error Alert
      • 8.2.7 Calibrate Pump Flow
      • 8.2.8 Calibrate Flow Meter
      • 8.2.9 Restore flow Meter to Factory Setting
    • 8.3 Remote Controller Settings
      • 8.3.1. Radio calibration
      • 8.3.2. Channel Monitor
      • 8.3.3. Advance Settings
    • 8.4 Compass Calibration Settings
      • 8.4.1. Compass
      • 8.4.2. Large Vehicle Calibration:
    • 8.5 IMU Calibration Settings
      • 8.5.1 Accelerometer Calibration:
      • 8.5.2 Level Horizon Sensor Calibration
      • 8.5.3 Barometer Calibration:
    • 8.6 Camera Settings
    • 8.7 General Settings
    • 8.8 AeroMegh / Enterprise Account
      • 8.8.1. Login:
      • 8.8.2. Account Details
  • 9. Field Plotting
    • 9.1. RC/Mobile:
    • 9.2. Drone
    • 9.3. Map
    • 9.4. Import KML
  • 10. Mission Planning
    • 10.1 Parameters
    • 10.2 Adjust Waypoint
    • 10.3 Adjust Spacing
    • 10.4 Indentation
    • 10.5 Obstacle Boundary
    • 10.6 Route Adjust
    • 10.7 Move Plan
    • 10.8 Plan Splitting
  • 11. Obstacle Avoidance
    • 11.1 Polygon Type Obstacle
    • 11.2 Circle Type Obstacles
    • 11.3 Edit Obstacles
    • 11.4 Delete Obstacle
  • 12. Flyview
    • 12.1 Flight Controls
    • 12.2 Flight Details
    • 12.3 Spray Rate Dosage Calculation
    • 12.4 Status details and settings option
    • 12.5 Range Finder
    • 12.6 Notifications
    • 12.7 Arm and Disarm Navigation Bar
  • 13. Report Generation
    • 13.1. View Report
    • 13.2. Generate Field Report
  • 14. Managing data
  • 15. Creating AeroGCS Enterprise Account
  • 16. Troubleshooting
Powered by GitBook
On this page

Was this helpful?

  1. 10. Mission Planning

10.1 Parameters

Previous10. Mission PlanningNext10.2 Adjust Waypoint

Last updated 6 months ago

Was this helpful?

AeroGCS GREEN provides support for the parameters listed below, as displayed in the following screen:

AeroGCS GREEN offers the ability to configure parameters by adjusting the position of slide bars on the screen. Users can easily set various parameters, including:

1. Spray Amount: Determines the volume of liquid sprayed, measured in liters per acre (L/Acre). Users can set it anywhere between a minimum of 1 L/Acre and a maximum of 50 L/Acre.

2. Spray Rate: Controls the rate of spraying, expressed as a percentage. Users can adjust it from a minimum of 10% to a maximum of 100%.

3. Spray Altitude: Specifies the altitude at which spraying occurs, with a minimum of 1 meter and a maximum of 15 meters.

4. Flight Speed: Allows users to set the flight speed, ranging from a minimum of 1 meter per second (m/s) to a maximum of 20 m/s.

5. Spacing: This parameter enables the user to modify the spacing between the polylines of the plan. Users can set the spacing anywhere between a minimum of 2 meters and a maximum of 10 meters.

6. Fence Boundary: The fence boundary parameter is used to establish a safety perimeter around the device. Users can adjust it within the range of 1 meter to 500 meters to safeguard the device and its operation.

Adjusting parameters